Tube Axial Duct Fans:

Fan Guards (Inlet & Outlet) – bolt mounted to the flanged end of the fan drum.
Belt Guards – a cage-like metal box that covers the belt and pulley.
Motor & Belt Cover – a cage- like metal box that covers the motor, belt and pulley.
Matching Flange – a stand-alone flange that can be mounted to duct work and connected directly to the fan inlet or outlet flange.
Mounting Legs – a solid steel support bolted to the bottom of the fan drum to provide standing support.
Vertical Mounting Brackets – (4) brackets welded to the flange of the fan drum with pre-drilled holes to enable vertical mounting of fan.
Horizontal Mounting Brackets – (4) brackets, (2) each welded on each end of the fan drum with pre-drilled holes to enable horizontal mounting of fan.
Coatings – Contact Americraft to discuss your specific fan application and we will help you select the best finish to meet your needs.
Variable Pitch Motor Sheave – provides flexibility to change the fan speed in the field to balance system needs (check motor amp load before and after changing the fan speed).
Inspection Access Door – A removable steel panel bolted to the side of the fan drum to allow access for inspection (not replacement) of fan parts.

Wall Exhaust Fans:

Aluminum Automatic Exhaust Shutters – a rear flanged gravity exhaust shutter ideal for use with direct-drive or belt-driven wall exhaust fans.

Motor Kit – includes 115V power-open/spring-close actuator to provide tighter closure of exhaust shutter.
Aluminum Motor Operated Center Pivot Damper – a motorized volume control damper used for exhaust or supply applications.
Rear Spiral Propeller Guard – Model 900 – Sizes 12, 16, 18, 24 – guard mounted between the motor and prop (factory installed only).
Rear Box Guard – Expanded Metal – box guard mounted to the rear of the fan panel.  Available for sizes 12″ through 60″.  Meets OSHA requirements.
Rear Box Guard – Welded Wire – box guard mounted to the rear of the fan panel.  Available for sizes 24″ through 60″.  Meets OSHA requirements.
Front Guard – Welded Wire – guard mounted to the fan panel in front of the prop  Available for sizes 12″ through 48″.  Meets OSHA requirements.
Front Guard – Wire Mesh – Models 800, 900 – Sizes 54″, 60″
Heavy Duty Fan & Shutter Mounting Box – Simplifies mounting in block, concrete or metal walls.  Also maintains the proper distance between the propeller and shutter.
Inlet Weather Hood with Bird Screen – mounted to the exterior wall to shelter the fan from wind, rain and birds/animals.  Recommended for intake fans.


Roof Exhausters/Ventilators:

Flat, Single, Double Pitch Insulated Roof Curbs:  a standard curb for all power roof exhausters measuring 8″ high with wood nailer.  Must specify type of roof construction and the roof pitch.  Not available for corrugated or standing seam roofs.  Contact Americraft for further information.
Damper Section Only with Mounting Ring
Raintight Disconnect Switch – the switch provides a safe and easy way of disconnecting power from the roof exhauster.  Switch is factory mounted and wired for customer specified voltage.
Coatings – Contact Americraft to discuss your specific fan application and we will help you select the best finish to meet your needs.

Cast Aluminum Blower:

Flexible Hose – wire reinforced rubber hose available in 5′ sections.
Stainless Steel Hose Clamps – connects the hose to the inlet/outlet of blower housing.
Inlet/Outlet Guard – a guard that protects objects from entering the unducted inlet or outlet side of the blower. Meets OSHA requirements.
Wall Mounting Bracket
Inlet/Outlet Flange – cast aluminum flange mounted to blower inlet and/or outlet to assist connection to ANSI pipe flanges.  Supplied undrilled unless otherwise directed.  Not available in down blast configuration.
Slide Gate Damper- Installed on the discharge side of the blower.  Allows for reduction of CFM to assist with balancing of system requirements.
Inlet Filters – filters the air passing through the inlet side of the blower with cleanable wire mess media.
Teflon Shaft Seal – seals motor shaft hole opening with minimal air leakage.

Motor Weather Cover – a cage-like metal box that covers the motor.

Man & Product Coolers:

Manual Starting Switch – includes built-in overload protection, mounted & wired for fans with TEFC motors only. NEMA I Enclosure.
Caster sets – includes two fixed and two swivel locking casters available on medium and low stands.